Skip to main content

MAX40660ATB/VY+, MAX40661ATB/VY+ Transimpedance Amplifier TDFN-10 from Maxim

The MAX40660 and MAX40661 are transimpedance amplifiers for optical distance measurement receivers in LiDAR applications. Low noise, high gain, low group delay, and fast recovery from overload make these TIAs ideal for distance-measurement applications. Important features include 2.38pA input-referred noise density MAX40660), an internal input clamp, pin-selectable 25kΩ and 50kΩ transimpedance, and wide bandwidth (490MHz (typ) for the MAX40660 with 0.5pF input capacitance and 25kΩ transimpedance; 160MHz (typ) for the MAX40661 with 10pF input capacitance). An offset current input allows optional adjustment of input offset current. A low-power/ standby control input reduces the supply current by better than 80% to help reduce average power supply current between pulses. The MAX40660 and MAX40661 transimpedance amplifiers feature AEC-Q100 qualification, enable ASIL compliance, and are available in a 3mm x 3mm,10-lead TDFN package with side-wettable flanks, making them excellent choices for automotive LiDAR applications.

AEC-Q100
Internal Clamp For Input Current Up To 2A (Transient)
Fast Overload Recovery: 2ns at 100mA
3.3V Operation
10-Pin TDFN (Side-Wettable) or Bare Die
Two Pin-Selectable Transimpedance Values 25kΩ and 50kΩ
-40°C to +125°C Operating Junction Temperature Range

Part Number Pin-Package CIN (pF) Bandwidth
MAX40660ATB+** 10-TDFN 0.25pF to 5pF 490 MHz
MAX40660ATB/VY+ 10-TDFN 0.25pF to 5pF 490 MHz
MAX40660C/D+** Dice* 0.25pF to 5pF 490 MHz
MAX40661ATB+** 10-TDFN 5pF to 12pF 160 MHz
MAX40661ATB/VY+ 10-TDFN 5pF to 12pF 160 MHz
MAX40661C/D+** Dice* 5pF to 12pF 160 MHz

*Dice are designed to operate over a -40°C to +100°C junction temperature (Tj) range, but are tested and guaranteed at TA = +25°C.
**Future product-Contact Maxim factory for availability.
T = Tape and reel. /V denotes an automotive qualified part.



Comments

Popular posts from this blog

Nordic Thingy: 91 Multi-sensor cellular IoT Prototyping kit

The Nordic Thingy:91 is an easy-to-use battery-operated prototyping platform for cellular IoT using LTE-M, NB-IoT and GPS. It is ideal for creating Proof-of-Concept (PoC), demos and initial prototypes in your cIoT development phase.
NRF6943  Nordic Thingy:91 is as Multi-sensor cellular IoT prototyping kit supporting LTE-M, NB-IoT, GPS and Bluetooth Low Energy.
The Nordic Thingy:91 is the ideal way to kickstart your cellular IoT project using the nRF9160 SiP. Thingy:91 is equipped with a broad collection of diverse sensors and interfaces that make it highly adaptable to rapid prototyping and getting your proof of concept off the ground in no time at all.

        Key features
•Battery-operated prototyping platform for the nRf9160 SiP
•700-900 MHz + 1710-2200 MHz LTE band support
•Certifications: CE, FCC
•nRF52840 multiprotocol SoC on board
•LTE-M/NB-IoT/GPS antennas
•Nano/4FF SIM card slot
•User-programmable button and RGB LEDs
•Environmental sensor for temp, humidity, air quality and a…

ON Semi RSL10-SOLARSENS-GEVK, RSL10 Solar Cell Multi-Sensor Platform

ON Semiconductor driving energy efficient innovations, continues to enable battery-less and maintenance-free IoT with the introduction of its RSL10 Multi-Sensor Platform powered solely with a solar cell. This complete solution supports the development of IoT sensors using continuous solar energy harvesting to gather and communicate data through Bluetooth® Low Energy, without the need for batteries or other forms of non-renewable energy.
The RSL10 Solar Cell Multi-Sensor platform is a complete, low-cost solution for developing self-powered sensor nodes using harvested solar energy. Based on the RSL10 SIP- the industry's lowest power Bluetooth ® 5 radio, the RSL10 Solar Cell Multi-Sensor platform supports continuous Bluetooth Low Energy transmission of sensor information without requiring any batteries. The fully-integrated platform features multiple smart sensors, an ultra-low quiescent current LDO regulator (NCP170), and a 2-port connector for the provided solar cell (FlexRB-25-70…

Arduino ASX00003 MKR Motor Carrier Board

The MKR Motor Carrier is an MKR add-on board designed to control servo, DC, and stepper motors. The Carrier can also be used to connect other actuators and sensors via a series of 3-pin male headers.

for more details please click this link  https://store.arduino.cc/usa/mkr-motor-carrier


The summary of features is shown below:

1.Compatible with all the boards in the MKR family 2.Four servo motor outputs 3.Four DC motor outputs (two high performance + two standard performance) 4.Sensing of current feedback for the high-performance motors 5.Two inputs for encoder sensors 6.Four inputs for analog sensors (3-pin compatible) 7.Possibility to read the status of the batteries 8.ON-OFF switch with Power ON LED 9.LiPo battery connector (2S or 3S compatible) and power terminal block for alternative power source 10.LEDs to visually indicate the direction of the rotation of the DC motors.
Source https://store.arduino.cc/usa/mkr-motor-carrier