Skip to main content

SST26VF064BEUI Flash Memory 64 Mbit Serial Quad I/O (SQI) from Microchip

The Serial Quad I/O™ (SQI™) family of flash-memory devices features a six-wire, 4-bit I/O interface that allows for low-power, high-performance operation in a low pin-count package. SST26VF032BEUI also support full command-set compatibility to traditional Serial Peripheral Interface (SPI) protocol. System designs using SQI flash devices occupy less board space and ultimately lower system costs.

Factory-programmed with EUI-48™ and EUI-64™ Global Unique Identifier
Burst Modes- Continuous linear burst, 8/16/32/64 Byte linear burst with wrap-around
age-Program- 256 Bytes per page in x1 or x4 mode
Industrial -40C to +85C
Single Voltage Read and Write Operations 2.7-3.6V or 2.3-3.6V
8-contact WDFN (6mm x 5mm)
8-lead SOIJ (5.28 mm)
8-lead SOIC (3.90 mm)

SST26VF064BEUI-104I/MF Flash Memory 64 Mbit Serial Quad I/O (SQI) WDFN-8
SST26VF064BEUI-104I/MF Flash Memory 64 Mbit Serial Quad I/O (SQI) WDFN-8
SST26VF064BEUIT-104I/MF Flash Memory 64 Mbit Serial Quad I/O (SQI) WDFN-8
SST26VF064BEUIT-104I/SM Flash Memory 64 Mbit Serial Quad I/O (SQI) SOIJ-8
SST26VF032BEUI-104I/SM Flash Memory 32 Mbit Serial Quad I/O (SQI) SOIJ-8
SST26VF032BEUIT-104I/SM Flash Memory 32 Mbit Serial Quad I/O (SQI) SOIJ-8
SST26VF016BEUI-104I/SN Flash Memory 16 Mbit Serial Quad I/O (SQI)  SOIC-8
SST26VF016BEUIT-104I/SN Flash Memory 16 Mbit Serial Quad I/O (SQI)  SOIC-8

Datasheets

Comments

Popular posts from this blog

Nordic Thingy: 91 Multi-sensor cellular IoT Prototyping kit

The Nordic Thingy:91 is an easy-to-use battery-operated prototyping platform for cellular IoT using LTE-M, NB-IoT and GPS. It is ideal for creating Proof-of-Concept (PoC), demos and initial prototypes in your cIoT development phase.
NRF6943  Nordic Thingy:91 is as Multi-sensor cellular IoT prototyping kit supporting LTE-M, NB-IoT, GPS and Bluetooth Low Energy.
The Nordic Thingy:91 is the ideal way to kickstart your cellular IoT project using the nRF9160 SiP. Thingy:91 is equipped with a broad collection of diverse sensors and interfaces that make it highly adaptable to rapid prototyping and getting your proof of concept off the ground in no time at all.

        Key features
•Battery-operated prototyping platform for the nRf9160 SiP
•700-900 MHz + 1710-2200 MHz LTE band support
•Certifications: CE, FCC
•nRF52840 multiprotocol SoC on board
•LTE-M/NB-IoT/GPS antennas
•Nano/4FF SIM card slot
•User-programmable button and RGB LEDs
•Environmental sensor for temp, humidity, air quality and a…

ON Semi RSL10-SOLARSENS-GEVK, RSL10 Solar Cell Multi-Sensor Platform

ON Semiconductor driving energy efficient innovations, continues to enable battery-less and maintenance-free IoT with the introduction of its RSL10 Multi-Sensor Platform powered solely with a solar cell. This complete solution supports the development of IoT sensors using continuous solar energy harvesting to gather and communicate data through Bluetooth® Low Energy, without the need for batteries or other forms of non-renewable energy.
The RSL10 Solar Cell Multi-Sensor platform is a complete, low-cost solution for developing self-powered sensor nodes using harvested solar energy. Based on the RSL10 SIP- the industry's lowest power Bluetooth ® 5 radio, the RSL10 Solar Cell Multi-Sensor platform supports continuous Bluetooth Low Energy transmission of sensor information without requiring any batteries. The fully-integrated platform features multiple smart sensors, an ultra-low quiescent current LDO regulator (NCP170), and a 2-port connector for the provided solar cell (FlexRB-25-70…

Arduino ASX00003 MKR Motor Carrier Board

The MKR Motor Carrier is an MKR add-on board designed to control servo, DC, and stepper motors. The Carrier can also be used to connect other actuators and sensors via a series of 3-pin male headers.

for more details please click this link  https://store.arduino.cc/usa/mkr-motor-carrier


The summary of features is shown below:

1.Compatible with all the boards in the MKR family 2.Four servo motor outputs 3.Four DC motor outputs (two high performance + two standard performance) 4.Sensing of current feedback for the high-performance motors 5.Two inputs for encoder sensors 6.Four inputs for analog sensors (3-pin compatible) 7.Possibility to read the status of the batteries 8.ON-OFF switch with Power ON LED 9.LiPo battery connector (2S or 3S compatible) and power terminal block for alternative power source 10.LEDs to visually indicate the direction of the rotation of the DC motors.
Source https://store.arduino.cc/usa/mkr-motor-carrier