Skip to main content

BM62380MUV-E2 3 Phase Brushless DC Motor VQFN from Rohm

Built-in Speed Control, 3 Hall Sensors Three-Phase Brushless Motor Driver

BM62380MUV is sine wave driver IC for three-phase brushless motor driver with 40 V power supply voltage rating and 2.0 A output current rating. It detects the rotor position by 3 Hall sensors. In addition, it has a speed feedback control function, and controls output PWM Duty by adjusting the rotational frequency characteristics for the input PWM signal and the rotational frequency affected from motor.

Operating Supply Voltage Range: 8 V to 28 V
Output current rating: 2.0 A
Output ON Resistance (top & bottom total): 0.6 Ω (Typ)
Output PWM Frequency: 40 kHz (Typ)
Standby Current: 0.6 mA (Typ)
Operating Temperature Range: -40 °C to +85 °C
Package  VQFN040V6060 6.00 mm x 6.00 mm x 1.00 mm

https://www.rohm.com/datasheet/BM62380MUV/bm62380muv-e

Comments

Popular posts from this blog

Nordic Thingy: 91 Multi-sensor cellular IoT Prototyping kit

The Nordic Thingy:91 is an easy-to-use battery-operated prototyping platform for cellular IoT using LTE-M, NB-IoT and GPS. It is ideal for creating Proof-of-Concept (PoC), demos and initial prototypes in your cIoT development phase.
NRF6943  Nordic Thingy:91 is as Multi-sensor cellular IoT prototyping kit supporting LTE-M, NB-IoT, GPS and Bluetooth Low Energy.
The Nordic Thingy:91 is the ideal way to kickstart your cellular IoT project using the nRF9160 SiP. Thingy:91 is equipped with a broad collection of diverse sensors and interfaces that make it highly adaptable to rapid prototyping and getting your proof of concept off the ground in no time at all.

        Key features
•Battery-operated prototyping platform for the nRf9160 SiP
•700-900 MHz + 1710-2200 MHz LTE band support
•Certifications: CE, FCC
•nRF52840 multiprotocol SoC on board
•LTE-M/NB-IoT/GPS antennas
•Nano/4FF SIM card slot
•User-programmable button and RGB LEDs
•Environmental sensor for temp, humidity, air quality and a…

ON Semi RSL10-SOLARSENS-GEVK, RSL10 Solar Cell Multi-Sensor Platform

ON Semiconductor driving energy efficient innovations, continues to enable battery-less and maintenance-free IoT with the introduction of its RSL10 Multi-Sensor Platform powered solely with a solar cell. This complete solution supports the development of IoT sensors using continuous solar energy harvesting to gather and communicate data through Bluetooth® Low Energy, without the need for batteries or other forms of non-renewable energy.
The RSL10 Solar Cell Multi-Sensor platform is a complete, low-cost solution for developing self-powered sensor nodes using harvested solar energy. Based on the RSL10 SIP- the industry's lowest power Bluetooth ® 5 radio, the RSL10 Solar Cell Multi-Sensor platform supports continuous Bluetooth Low Energy transmission of sensor information without requiring any batteries. The fully-integrated platform features multiple smart sensors, an ultra-low quiescent current LDO regulator (NCP170), and a 2-port connector for the provided solar cell (FlexRB-25-70…

Arduino ASX00003 MKR Motor Carrier Board

The MKR Motor Carrier is an MKR add-on board designed to control servo, DC, and stepper motors. The Carrier can also be used to connect other actuators and sensors via a series of 3-pin male headers.

for more details please click this link  https://store.arduino.cc/usa/mkr-motor-carrier


The summary of features is shown below:

1.Compatible with all the boards in the MKR family 2.Four servo motor outputs 3.Four DC motor outputs (two high performance + two standard performance) 4.Sensing of current feedback for the high-performance motors 5.Two inputs for encoder sensors 6.Four inputs for analog sensors (3-pin compatible) 7.Possibility to read the status of the batteries 8.ON-OFF switch with Power ON LED 9.LiPo battery connector (2S or 3S compatible) and power terminal block for alternative power source 10.LEDs to visually indicate the direction of the rotation of the DC motors.
Source https://store.arduino.cc/usa/mkr-motor-carrier