Skip to main content

Trinamic New TMC6200-TA MOSFET Gate Driver for High-Power BLDC/PMSM Motors

The TMC6200 is the new high-voltage gate-driver with in-line motor current sensing for BLDC motors and PMSM servo motors of up to 100A using external MOSFETs.

3-phase motors up to 100A coil current (external MOSFETs)
Voltage range 8 to 60V DC
Programmable gate drive (0.5A / 1A / 1.5A)
Full protection and diagnostics via SPI interface
SPI & Stand-Alone operation
Charge Pump for 100% Duty Cycle operation
Optional BBM break-before-make logic for single line control
Programmable Short and Overload current threshold and retry
Programmable Control Interface with 3 line or 6 line drive
Compact 9x9mm2 TQFP48 package
Double Pin Distance for safe operation at high voltage

TMC6200-TA Three phase gate-driver for external MOSFETs; TQFP48 
TMC6200-TA-T Three phase gate-driver for external MOSFETs; TQFP48 , Reel
TMC6200-EVAL Evaluation board for TMC6200.
LANDUNGSBRÜCKE Baseboard for TMC6200-EVAL and further evaluation boards.
ESELSBRÜCKE Connector board for plug-in evaluation board system.

Datasheet TMC6200-EVAL, TMC6200-BOB

Comments

Popular posts from this blog

Nordic Thingy: 91 Multi-sensor cellular IoT Prototyping kit

The Nordic Thingy:91 is an easy-to-use battery-operated prototyping platform for cellular IoT using LTE-M, NB-IoT and GPS. It is ideal for creating Proof-of-Concept (PoC), demos and initial prototypes in your cIoT development phase.
NRF6943  Nordic Thingy:91 is as Multi-sensor cellular IoT prototyping kit supporting LTE-M, NB-IoT, GPS and Bluetooth Low Energy.
The Nordic Thingy:91 is the ideal way to kickstart your cellular IoT project using the nRF9160 SiP. Thingy:91 is equipped with a broad collection of diverse sensors and interfaces that make it highly adaptable to rapid prototyping and getting your proof of concept off the ground in no time at all.

        Key features
•Battery-operated prototyping platform for the nRf9160 SiP
•700-900 MHz + 1710-2200 MHz LTE band support
•Certifications: CE, FCC
•nRF52840 multiprotocol SoC on board
•LTE-M/NB-IoT/GPS antennas
•Nano/4FF SIM card slot
•User-programmable button and RGB LEDs
•Environmental sensor for temp, humidity, air quality and a…

ON Semi RSL10-SOLARSENS-GEVK, RSL10 Solar Cell Multi-Sensor Platform

ON Semiconductor driving energy efficient innovations, continues to enable battery-less and maintenance-free IoT with the introduction of its RSL10 Multi-Sensor Platform powered solely with a solar cell. This complete solution supports the development of IoT sensors using continuous solar energy harvesting to gather and communicate data through Bluetooth® Low Energy, without the need for batteries or other forms of non-renewable energy.
The RSL10 Solar Cell Multi-Sensor platform is a complete, low-cost solution for developing self-powered sensor nodes using harvested solar energy. Based on the RSL10 SIP- the industry's lowest power Bluetooth ® 5 radio, the RSL10 Solar Cell Multi-Sensor platform supports continuous Bluetooth Low Energy transmission of sensor information without requiring any batteries. The fully-integrated platform features multiple smart sensors, an ultra-low quiescent current LDO regulator (NCP170), and a 2-port connector for the provided solar cell (FlexRB-25-70…

Arduino ASX00003 MKR Motor Carrier Board

The MKR Motor Carrier is an MKR add-on board designed to control servo, DC, and stepper motors. The Carrier can also be used to connect other actuators and sensors via a series of 3-pin male headers.

for more details please click this link  https://store.arduino.cc/usa/mkr-motor-carrier


The summary of features is shown below:

1.Compatible with all the boards in the MKR family 2.Four servo motor outputs 3.Four DC motor outputs (two high performance + two standard performance) 4.Sensing of current feedback for the high-performance motors 5.Two inputs for encoder sensors 6.Four inputs for analog sensors (3-pin compatible) 7.Possibility to read the status of the batteries 8.ON-OFF switch with Power ON LED 9.LiPo battery connector (2S or 3S compatible) and power terminal block for alternative power source 10.LEDs to visually indicate the direction of the rotation of the DC motors.
Source https://store.arduino.cc/usa/mkr-motor-carrier